Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Forks

$9.99
- Protective neoprene and velcro cut-To-Fit boot fits most rear shocks
$15.90
- Clamps on to dual-Crown fork stanchions to prevent damage to frame - Easy to install and adjust, More secure and lower profile than stock bumpers - Molded loops allow clean and easy zip-Tie number plate mounting - Available for 35mm boxxer or 40mm fox stanchions, Sold in pairs
$17.00 - $43.00
Service kits include dust seals, foam rings, oil seals, air and damper o-rings needed for basic service.
$21.50
- Replacement leg guards for Dorado forks
$27.00
Service your suspension fork with Enduro Seal KIts. - Custom made for each make and model of fork
$39.99 - $49.99 $49.99 - $59.99 Up to 33% Off
Economically priced hi-tensile steel MTB fork for 26-inch wheels. - Steerer Type: Threaded Steerer - Size: 1" (7/8 ID) - Steerer Length: 198mm - Rake: 45mm - Axle-to-Crown: 393mm - Race Diameter: 27mm - Axle: 3/8" - Thread Length: 95mm
$45.99 - $49.99
• Caliper brake mounts • 35mm rake • High-tensile steel construction • 1-inch steerer diameter • 185mm steerer length • Threaded fork • Compatible with 20-inch wheels
$49.99
- Hi-tensile steel construction - Caliper brake mount - 35mm rake - Axle-to-Crown: 365mm - Race Diameter: 27mm - Axle: 3/8-inch - Thread Length: 120mm - Steerer Length: 200mm - Steerer Size: 1-inch
$49.99
- Hi-tensile steel construction - Caliper brake mount - 35mm rake - Steerer Type: Threaded - Steerer Size: 1-inch - Steerer Length: 200mm - Brake Mount: Caliper - Axle-to-Crown: 395mm - Race Diameter: 27mm - Axle: 3/8-inch - Thread Length: 100mm
$49.99
- Hi-tensile steel construction - Caliper brake mount - 35mm rake - Steerer Type: Threaded - Steerer Size: 1-inch - Steerer Length: 137mm - Brake Mount: Caliper - Rake: 35mm - Axle-to-Crown: 315mm - Race Diameter: 27mm - Axle: 3/8-inch - Thread Length: 40mm
$49.99 - $65.99
• Cantilever brake mounts • High-tensile steel construction • Threaded fork • Steerer diameter: 1-inch • Steerer length: 200mm • For bikes with 26-inch wheels
$54.76
- Hi-tensile steel construction - Available with brake studs or without - 60mm rake - Type: Cruiser Size: 26" - Steerer Type: Threaded Steerer - Steerer Length: 250mm - Axle-to-Crown: 400mm - Axle: 3/8" - Thread Length: 125mm - O.L.D.: 100mm
$59.99 - $65.00
- Brake mounts: Caliper - Construction: Hi-tensile steel - Rake: 50mm - Type: LW - Steerer type: Threaded - Race diameter: 27mm - Axle: 3/8'inch
$59.99
• Cantilever brake mounts • High-tensile steel construction • Threaded fork • Steerer diameter: 1-inch • Steerer length: 180mm
$59.99
• Cantilever brake mounts • High-tensile steel construction • Threaded fork • Steerer diameter: 1-inch • Steerer length: 200mm
$59.99
• High-tensile steel construction • Threadless
$69.99 - $79.99
- Cantilever brake mounts - 45mm rake - Hi-tensile steel construction - Steerer Type: Threaded - Steerer Size: 1-inch - Brake Mount: Cantilever - Rake: 45mm - Axle-to-Crown: 405mm - Thread Length: 120mm - Axle: QR 9mm
$69.99 - $79.99
• Cantilever brake mounts • 45mm rake • High-tensile steel construction • Threaded fork
$74.99
- Cantilever brake mounts - High-tensile steel construction - Threadless fork - Steerer diameter: 1 1/8-inch - Steerer length: 260mm - For bikes with 26-inch wheels
$87.99 - $89.99
• Caliper brake mounts • 385mm axle-to-crown • Chromoly construction • 1-inch steerer diameter • Threaded fork
$89.99
- Forged dropouts with eyelets, straight-gauge oval tapered blades - Dimension Forks are intended for general recreational riding only; they are not intended for aggressive riding, stunt riding or road racing - 85mm threaded section - Fits up to 30c tires - Axle to Crown Length: 382 mm - Brake Mount (Fork): Long Reach Caliper (55mm - 73mm) - Crown Race: 27 - Front Axle: 9mm x 100mm - Material: Steel - Offset: 50mm - S.H.I.S. Stem Clamp Diameter: 25.4-24tpi Quill - Steerer Type: Straight - Weight: 839g, 876g, 907g - Wheel Size: 27"
$89.99
Dimension Rigid Mountain Forks are intended for general recreational riding only; they are not intended for aggressive riding, stunt riding or road racing. - Forged dropouts with eyelets - Chromoly tubing - Cantilever mounts only (no disc mount) - Axle to Crown Length: 395mm - Brake Mount (Fork): Canti Studs - Crown Race: 30 - Front Axle: 10mm x 100mm - Maximum Tire Clearance (Fork): 3.8 - Offset: 45mm - S.H.I.S. Stem Clamp Diameter: 25.4 - Steer Tube length: 260mm - Steerer Type: Straight - Weight: 1000g - Wheel Size: 26-inch
$89.99
700c Hybrid fork with Cantilever Mounts - Forged dropouts with eyelets, straight-gauge oval-tapered blades - Dimension Forks are intended for general recreational riding only; they are not intended for aggressive riding, stunt riding or road racing - Welded unicrown construction - Clearance for 50mm wide fenders (1 1/8-inch) - Axle to Crown Length: 403mm (1 1/8-inch); 412mm (1 1/8-inch SC); 403mm (1-inch) - Brake Mount (Fork): Canti Studs - Color: Black - Crown Race: 30 (1 1/8-inch, 1 1/8-inch SC); 26 (1-inch) - Front Axle: 10mm x 100mm - Material: Steel - Offset: 50 mm - S.H.I.S. Stem Clamp Diameter: 28.6 (1 1/8-inch, 1 1/8-inch SC); 25.4 (1-inch) - Steerer Tube Length: 300mm (1 1/8-inch); 260mm (1 1/8-inch SC); 300mm (1-inch) - Steerer Type: Straight - Weight: 975g (1 1/8-inch); 1105g (1 1/8-inch SC); 963g (1-inch) - Wheel Size: 700c
$89.99
Dimension Road Forks are intended for general recreational riding only; they are not intended for aggressive riding, stunt riding or road racing. - Forged dropouts with eyelets, welded unicrown construction - Designed for short-reach caliper brakes - 25 x 14mm tapered oval blades - Axle to Crown Length: 374mm - Brake Mount (Fork): Short Reach Caliper (39mm-49mm) - Color: Black - Crown Race: 30 - Defined Color: Black - Front Axle: 10mm x 100mm - Material: Steel - Offset: 50mm - S.H.I.S. Stem Clamp Diameter: 28.6 - Steerer Tube Length (mm): 300 - Steerer Type: Straight - Weight: 773g (1-inch); 780g (1 1/8-inch) - Wheel Size: 700c
$89.99 - $103.99
• Chromoly construction • V-brake mounts • Fits bikes with 16-inch wheels • Steerer length: 250mm
$89.99
• Cantilever brake mounts • 45mm rake • Chromoly construction • 1 1/8-inch steerer diameter • Threadless fork
$89.99 - $99.99
• Caliper brake mounts • 45mm rake • Chromoly construction • Threadless fork • 300mm steerer length
$93.99 - $119.99
• Chromoly construction • V-brake mounts • I.S. disc mount • Fits bikes with 20-inch wheels • Steerer length: 250mm
$97.90
- Replacement damper kits
$99.99
- Hi-Tensile steel construction - 135mm fat tire front hub spacing - Steerer Type: Threadless - Steerer Size: 1-1/8-inch - Steerer Length: 275mm - Brake Mount: Is Disc - Rake: 45mm - Axle-to-Crown: 450mm - Race Diameter: 30mm - Axle: QR 9mm
$99.99
• High-tensile steel construction • Springer suspension • Threaded • 1-inch diameter (7/8-inch inner diameter) • 20-inch version steerer length: 148mm • 26-inch version steerer length: 180mm
$99.99
• Cantilever brake mounts • Chromoly construction • Threaded fork • For 26-inch wheels • 200mm steerer length
$99.99
• Cantilever brake mounts • 45mm rake • Chromoly construction • 1-inch steerer diameter • 250mm steerer length • Threaded fork
$109.99
- Designed to match the Pake Rum Runner Track frames - Straight legs with unicrown CrMo construction - 300mm CrMo steerer with 38mm rake
$109.99
• Cantilever brake mounts • 45mm rake • Chromoly construction • 1-inch steerer diameter • 200mm steerer length • Threaded fork
$109.99 - $139.99
- Replacement urban threadless forks - Accepts up to 40mm tire width - Chromoly construction - 1-1/8" steer tube - Size: 700C - Steerer Type: Threadless - Steerer Length: 300mm - Material: Chromoly - Offset: 45mm - Axle-to-Crown: 405mm - Race Diameter: 30mm - Axle: QR
$119.99
From the pavement to the gravel, Origin-8's Cromo-Lite Disc Road Fork is made to explore. Crafted from super tough 4130 cromoly, it provides a comfortable ride with room for 28c tires for added control. And, it features mounts for disc or caliper brakes so you can ride your way.
$119.99
- Add a disc brake to any track bike with IS disc mounts for 160mm rotor - Straight legs with unicrown CrMo construction - 300mm CrMo steerer - Forward facing dropouts for easy wheel removal - Black fork is designed to match the Pake Rum Runner Track frames
$119.99
• Cantilever brake mounts • Chromoly construction • Threadless fork • For 26-inch wheels • 250mm steerer length • 1 1/8-inch steerer diameter
$125.00
This beaut here was designed alongside our Midnight Special Frame. In an effort to shed a few grams (it's for a road bike after all), we opted to utilize a unicrown design rather than a lugged one. In addition to the weight savings, it also looks really nice—don't you think? Now, we don't throw the phrase "future-proof" around lightly, so we won't use it here either. What we will say is that, like the Midnight Special Frame, this fork is equipped with modern road standards like flat mount disc brakes and a 100mm x 12mm thru-axle. For increased versatility, it has braze-ons for fenders and racks (including mid-blade!). - Axle-to-crown: 400mm - Steerer: 350mm, 1-1/8" straight - Tire Clearance: 27.5" x 2.32" or 700c x 42mm (27.5 x 1.95" or 700c x 38mm w/fenders) - Weight: 1254g
$129.99
Origin-8's Cromo-Lite Combo Mountain Fork is seriously versatile. This 4130 chromoly steel fork can be used with 26- or 29-inch wheels, and is suspension corrected for a 100mm 26-inch-wheel fork. With disc mounts and linear-pull brake bosses, even your brake choices are versatile.
$129.99
Origin-8's Cromo-Lite Combo Mountain Fork is a versatile fork for your 26-inch wheeled bike. Crafted from 4130 chromoly steel, it provides a compliant ride that's suspension corrected for excellent handling. With disc mounts and linear-pull brake bosses, you're set to mount the brakes you want.
$130.00
Looking to go rigid? Then check out Salsa's 80mm suspension-corrected CroMoto Grande mountain bike fork. This chromoly beauty boasts ISO disc tabs for premium braking and it's 1-1/8" straight steerer lets you use it on older frames, or brand-spanking-new ones. It features Salsa's famous, forward-facing stainless steel fork ends and has room for tires up to 90mm wide. Plus, it comes with fender eyelets so you can stay clean even when it's sloppy out. - Salsa Classico CroMoly - Forward-facing, stainless steel dropouts - 1-1/8? threadless steerer (260mm) - 468mm axle-to-crown - 45mm rake - ISO disc tabs - Tire clearance = 90mm - Fender eyelets -1080g with full-length steerer tube
$130.00
The Bridge Club fork is designed around the 27.5 wheel size with tire clearance up to 2.8, but is also capable of running 700c wheel setups with max tire clearance of 47c. It has 51mm I.S. disc caliper mounts and brake line guides as well. It only has the barnacles that matter most to the discerning bike tourist. The fork features upper and lower barrel bosses, one three pack mount on each leg, mid-blade eyelets, and rack mounts on the fork ends. - Axle-to-crown: 420mm - Offset: 43 - Steerer: 340mm - Tire Clearance: 71mm (2.8") - Weight: 1190g (2.62 lbs)
$130.00
Our lugged and brazed Cross-Check fork has room for 700c x 45mm tires and fenders. It’s made from 4130 CroMoly steel and features fender eyelets at the dropouts, cantilever brake pivots, and now has through-leg mid-blade eyelets for mounting a rack. The eyelets are threaded 5 x 1mm and located 165mm up from the axle. Finish is powdercoat. - Axle-to-crown: 400mm - Offset: 44mm - Steerer: 300mm - Tire Clearance: 700c x 45mm - Weight: 2.3 lb (1.0kg) uncut
$130.00
The ECR fork is much like the Ogre fork. Both are CroMoly 29er forks. Both work with frames designed for 80mm-travel suspension forks. Both feature 51mm I.S. disc caliper mounts, brake line guides, accommodations for a rack and fender, and 2 sets of cage mounts (one on each leg) that let you mount large size or standard water bottle cages. Both are designed to run just about any combination of parts and accessories you'd want on a fork and are finished in durable black powdercoat. The only real differences are 1) ECR is disc brake only, and 2) ECR's offset is 47mm, 5mm more than Ogre's. - Axle-to-crown: 468mm - Offset: 47mm - Steerer: 260mm, 1-1/8" straight - Tire Clearance: 29 x 3.0" - Weight: 3.1 lb (1.4kg) uncut
$130.00
Designed for Surly's Krampus frame, this fork has quick-release dropouts spaced at 100mm and clearance for a 3-inch tire on a 50mm rim. To accommodate such big tires it's got a longer axle-to-crown measurement than the Ogre or Karate Monkey forks, making it a perfect rigid fork option for lots of 29ers out there. The Krampus fork's blades were designed and manufactured specifically to play well with the unique forces such a long fork with big tires will encounter, and the steer tube is standard 1-1/8-inch threadless. It has line guides for a disc brake line as well as thru-blade eyelets and Three-Pack bosses on both fork legs. - Axle-to-crown: 483mm - Offset: 47mm - Steerer: 260mm - Tire Clearance: 29 x 3" - Weight: 1133g uncut
$130.00
The Long Haul Trucker fork is designed to mount racks and fenders and to haul stuff. The fork’s new crown provides ample clearance for 26 x 2.1 tires and sports threaded eyelets in four locations (dual dropout, midblade and fork crown) to provide more options for mounting stuff, from racks to whatever. Options galore. Curved blades, CroMoly steel. 1-1/8-inch threadless steer tube. - Axle-to-crown: 26" = 376mm - Offset: 45mm - Steerer: 26" (42–54cm frames) = 300mm; 26" (56–62cm frames) = 400mm - Tire Clearance: 26 x 2.1" - Weight: 26" = 2.1 lb (0.97kg) uncut
$130.00
The Long Haul Trucker fork is designed to mount racks and fenders and to haul stuff. Offered in 26? and 700c wheel sizes, the fork’s new crown provides ample clearance for 700c x 50mm tires, and sports threaded eyelets in four locations (dual dropout, midblade and fork crown) to provide more options for mounting stuff, from racks to whatever. Options galore. Curved blades, CroMoly steel. 1-1/8-inch threadless steer tube. - Axle-to-crown: 700c = 390mm - Offset: 45mm - Steerer: 700c (56–64cm frames) = 350mm - Tire Clearance: 700c x 45mm - Weight: 700c = 2.3 lb uncut
$130.00
Surly's Moonlander Fork has clearance for a 26 x 4.7-inch wide tire. It accepts specialty front hubs with a rear disc offset or 135mm rear hubs. It takes a front disc-brake adapter so you can run any brakes that come in a traditional front/rear set without having to break up a set. This fork features large-diameter, thin-wall chromoly blades that taper for a smooth and supple ride. And, it's got standard and low-rider rack mounts and comes in a tough powdercoat finish because it's awesome.
$130.00
The Ogre fork is non-suspension corrected and will run 29-inch as well as 27.5-inch tire options. Made of 4130 CroMoly, it's got 51mm IS disc mounts, removable cantilever pivots, brake-line guides, low-blade threaded barrel bosses and mid-blade eyelets for a rack. This fork is designed to run disc brakes, fenders and a rack simultaneously. It's got two sets of triple bottle mounts, one on each leg. - Axle to Crown Length: 447 mm - Brake Mount: Canti studs, IS Disc Brake 160 - Crown Race: 30 - Front Axle: 9mm x 100mm - Material: Chromoly Steel - Offset: 43 mm - Steerer Type: Straight 1-1/8-inch - Wheel Size: 29-inch, 27.5+ - Powdercoat finish
$130.00
Surly's Steamroller Fork pairs great handling with urban utility. It has steep track geometry for lightening fast response, making it as at home on the velodrome as it is flying downtown with cars and pedestrians. It features a flat crown, drilled to accept a standard-reach caliper brake, and the use of wide 38mm tires. And its stealthy Black powdercoat means your opponents in the Pursuit race will never see you coming!
$130.00
The Troll Fork is just like the one that comes with the Troll frame, a 26-inch wheeled fully geared utility bruiser and cruiser. Like all Surly's forks, it's constructed of CroMoly steel. It sports removable rim brake pivots as well as a 51mm disc caliper mount. The Troll Fork is designed to accept a rack while using a disc brake, via through-blade threaded mounts in two places on each fork blade, and it's even got fender eyelets. - Disc or rim brake compatible - Compatible with disc brakes and rack simultaneously - Fits 26-inch wheels with clearance for a 3.0-inch tire - Steerer Type: Straight 1-1/8-inch - Sleek powdercoat finish
$134.99
Odyssey's 41-Thermal forks quickly established a reputation for strength and quality when they originally introduced them in 1999, and they have since gone on to change the standards that all forks are judged by. The new R-Series forks continue this tradition. FEATURES - Fully redesigned. - Laboratory tested and team proven. - New, custom, seamless, tapered, butted and specially formed leg tube shaping for improved grind and guard clearance. - All-new steerer tube design improves fatigue strength and includes a built-in, integrated, lower headset seat race. - New, optimized, 4mm dropout shape for grind and peg clearance. - Updated 7075-T6 pre-load bolt - Proven 41-Thermal® processed 4130 chromoly - Legendary lifetime replacement warranty SPECS - 25mm traditional offset - 3/8” axle slots only Starting at 1lb 15.2oz (885 grams)
$135.00
Classic 100% chromoly construction and engineered for modern accessories, that's Surly's Long Haul Trucker Disc Fork. Its beautiful curved blades are brazed to a lovely and tough investment-cast crown and dropouts. There are disc-brake mounts and eyelets for fenders and mounts for a standard or low-rider rack. Plus, it boasts a tough powdercoat finish that's tres chic. - 100% CroMoly steel construction, curved blades, powdercoated - Extensive mounting options with threaded eyelets in four locations: double eyelet dropouts, mid-blade, and a pair drilled into the fork crown - 51mm IS disc brake mount - 26" has clearance for a 2.1" tire
$135.00
Classic 100% chromoly construction and engineered for modern accessories, that's Surly's Long Haul Trucker Disc Fork. Its beautiful curved blades are brazed to a lovely and tough investment-cast crown and dropouts. There are disc-brake mounts and eyelets for fenders and mounts for a standard or low-rider rack. Plus, it boasts a tough powdercoat finish that's tres chic. - 100% CroMoly steel construction, curved blades, powdercoated - Extensive mounting options with threaded eyelets in four locations: double eyelet dropouts, mid-blade, and a pair drilled into the fork crown - 51mm IS disc brake mount - 700c has clearance for a 45mm tire
$135.00
The Straggler fork is very much like the Cross-Check fork — it's a lugged and brazed CroMoly fork with room for 700c tires up to 50mm wide. Both feature fender and rack mount eyelets at the dropouts, mid-blade threaded rack mounts and threaded eyelets on the sides of the crown for accessories. Both deliver a resilient ride and are finished in black powdercoat. The Straggler fork is equipped with a 51mm I.S. disc caliper mount and no accommodation for rim brakes. - Axle-to-crown: 400mm - Offset: 44mm - Steerer: 300mm, 1-1/8" straight (42-58cm), 350mm, 1-1/8" straight (60-62cm) - Tire Clearance: 50mm (w/o fender) Weight: 2.5 lb (1.15kg) uncut
$139.00
Salsa Firestarter Fork - Mid-blade and dropout rack mounts - Anything Cage mounts on front of fork - Axle to Crown Length: 483 mm - Brake Mount (Fork): IS Disc Brake 160 - Crown Race: 30 - Front Axle: 9mm x 100mm - Material: Steel - Wheel Mount Center Offset (mm): 0 - S.H.I.S. Stem Clamp Diameter: 28.6 - Steerer Type: Straight - Steerer Tube Length (mm): 300 mm - Weight: 1190 g - Wheel Size: 27.5+ , 29" , 700c - Maximum Tire Clearance (Fork): 3
$144.99 - $169.99
Made from revised 100% Cult Classic tubing for increased strength and then 100% post-weld heat treated. 1-pc machined steerer tube with an integrated bearing race, tapered legs, and plenty of tire clearance.
$144.99
Made from revised 100% Cult Classic tubing for increased strength and then 100% post-weld heat treated. Investment cast 1pc drop outs for maximum strength and a super sleek finish. Features an updated top cap retention design. - 1-pc machined steerer tube with an integrated bearing race - Tapered legs - Tire clearance for 2.40” tires - Updated top cap retention design
Page 1 of 4 Next page